ITExamDump 의 학습가이드에는Cisco 642-883인증시험의 예상문제, 시험문제와 답입니다. 그리고 중요한 건 시험과 매우 유사한 시험문제와 답도 제공해드립니다. ITExamDump 을 선택하면 ITExamDump 는 여러분을 빠른시일내에 시험관련지식을 터득하게 할 것이고Cisco 642-883인증시험도 고득점으로 패스하게 해드릴 것입니다.
IT인증시험은 국제적으로 인정받는 자격증을 취득하는 과정이라 난이도가 아주 높습니다. Cisco인증 642-883시험은 IT인증자격증을 취득하는 시험과목입니다.어떻게 하면 난이도가 높아 도전할 자신이 없는 자격증을 한방에 취득할수 있을가요? 그 답은ITExamDump에서 찾을볼수 있습니다. ITExamDump에서는 모든 IT인증시험에 대비한 고품질 시험공부가이드를 제공해드립니다. ITExamDump에서 연구제작한 Cisco인증 642-883덤프로Cisco인증 642-883시험을 준비해보세요. 시험패스가 한결 편해집니다.
시험 번호/코드: 642-883
시험 이름: Cisco (Deploying Cisco Service Provider Network Routing (SPROUTE) )
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 82 문항
업데이트: 2013-11-06
Cisco인증 642-883시험을 준비하기 위해 잠도 설쳐가면서 많이 힘들죠? ITExamDump덤프가 고객님의 곁을 지켜드립니다. ITExamDump에서 제공해드리는Cisco인증 642-883덤프는 실제Cisco인증 642-883시험문제를 연구하여 만든 공부자료이기에 최고의 품질을 자랑합니다. ITExamDump덤프를 열심히 공부하여 멋진 IT전문가의 꿈을 이루세요.
ITExamDump의 제품을 구매하시면 우리는 일년무료업데이트 서비스를 제공함으로 여러분을 인증시험을 패스하게 도와줍니다. 만약 인증시험내용이 변경이 되면 우리는 바로 여러분들에게 알려드립니다.그리고 최신버전이 있다면 바로 여러분들한테 보내드립니다. ITExamDump는 한번에Cisco 642-883인증시험을 패스를 보장합니다.
ITExamDump는 여러분이 빠른 시일 내에Cisco 642-883인증시험을 효과적으로 터득할 수 있는 사이트입니다.Cisco 642-883덤프는 보장하는 덤프입니다. 만약 시험에서 떨어지셨다고 하면 우리는 무조건 덤프전액 환불을 약속 드립니다. 우리ITExamDump 사이트에서Cisco 642-883관련자료의 일부분 문제와 답 등 샘플을 제공함으로 여러분은 무료로 다운받아 체험해보실 수 있습니다. 체험 후 우리의ITExamDump에 신뢰감을 느끼게 됩니다. ITExamDump의Cisco 642-883덤프로 자신 있는 시험준비를 하세요.
ITExamDump의Cisco인증 642-883시험대비 덤프는 가격이 착한데 비하면 품질이 너무 좋은 시험전 공부자료입니다. 시험문제적중율이 높아 패스율이 100%에 이르고 있습니다.다른 IT자격증에 관심이 있는 분들은 온라인서비스에 문의하여 덤프유무와 적중율등을 확인할수 있습니다. Cisco인증 642-883덤프로 어려운 시험을 정복하여 IT업계 정상에 오릅시다.
Cisco 인증642-883인증시험공부자료는ITExamDump에서 제공해드리는Cisco 인증642-883덤프가 가장 좋은 선택입니다. ITExamDump에서는 시험문제가 업데이트되면 덤프도 업데이트 진행하도록 최선을 다하여 업데이트서비스를 제공해드려 고객님께서소유하신 덤프가 시장에서 가장 최신버전덤프로 되도록 보장하여 시험을 맞이할수 있게 도와드립니다.
642-883 덤프무료샘플다운로드하기: http://www.itexamdump.com/642-883.html
NO.1 When troubleshooting OSPF neighbor errors, which three verification steps should be considered.?
(Choose three.)
A. Verify if neighboring OSPF interfaces are configured in the same area.
B. Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
C. Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
D. Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
E. Verify if neighboring OSPF interfaces are configured with the same area type.
Answer: A,D,E
Cisco 642-883기출문제 642-883최신덤프 642-883 642-883자격증 642-883
NO.2 Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)
A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering
Answer: A,C
Cisco덤프 642-883기출문제 642-883
NO.3 Refer to the PE1 router routing table output exhibit.
What is causing the i su 10.1.10.0/24 [115/30] via 0.0.0.0, 00:40:34, Null0 entry on the PE1 router routing
table?
A. The PE1 router is receiving the 10.1.10.0/24 summary route from the upstream L1/L2 IS-IS router.
B. The PE1 router has been configured to summarize the 10.1.10.x/32 IS-IS routes to 10.1.10.0/24.
C. The 10.1.10.0/24 has been suppressed because IS-IS auto-summary has been disabled on the PE1
router.
D. The 10.1.10.0/24 has been suppressed because of a route policy configuration on the PE1 router.
E. The 10.1.10.0/24 has been suppressed because the more specific 10.1.10.x/32 IS-IS routes have
been configured to leak into the IS-IS non-backbone area.
Answer: B
Cisco 642-883최신덤프 642-883덤프
NO.4 In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?
A. ASBR on a normal OSPF area
B. ASBR on NSSA
C. ABR on totally stubby OSPF area
D. ABR on stubby OSPF area
E. ABR on a normal OSPF area
Answer: C
Cisco 642-883최신덤프 642-883덤프 642-883덤프 642-883자격증
NO.5 Which three statements are true regarding the OSPF router ID? (Choose three.)
A. The OSPF routing process chooses a router ID for itself when it starts up.
B. The router-id command is the preferred procedure to set the router ID.
C. If a loopback interface is configured, its address will always be preferred as the router ID over any
other methods.
D. After the router ID is set, it does not change, even if the interface that the router is using for the router
ID goes down. The router ID changes only if the router reloads or if the OSPF routing process restarts.
E. In OSPF version 3, the OSPF router ID uses a 128-bit number.
Answer: A,B,D
Cisco 642-883 642-883기출문제 642-883 642-883 dumps
NO.6 On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF
in area 0?
A. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 255.255.255.255
area 0
C. router ospf 1 area 0 interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0
E. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
F. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
Answer: C
Cisco기출문제 642-883 642-883자료
NO.7 Which four statements are correct regarding IS-IS operations? (Choose four.)
A. By default, Level 1 routers within an IS-IS area do not carry any routing information external to the area
to which they belong. They use a default route to exit the area.
B. Summarization should be configured on the Level 2 routers, which injects the Level 2 routes into Level
1.
C. IS-IS supports "route leaking" in which selected Level 2 routes can be advertised by a Level 1/Level 2
router into Level 1.
D. The IS-IS backbone is a contiguous collection of Level 1 capable routers, each of which can be in a
different area.
E. With IS-IS, an individual router is in only one area, and the border between areas is on the link that
connects two routers that are in different areas.
F. Cisco IOS XR Software supports multitopology for IPv6 IS-IS unless single topology is explicitly
configured in IPv6 address-family configuration mode.
Answer: A,C,E,F
Cisco 642-883덤프 642-883
NO.8 What is function of the RP/0/RSP0/CPU0:PE1(config-ospf)#distance Cisco IOS-XR command?
A. To modify the administrative distance of the OSPF routes
B. To modify the default seed metric of the OSPF external routes
C. To modify the OSPF default reference bandwidth
D. To modify the OSPF cost
Answer: A
Cisco 642-883시험문제 642-883최신덤프
NO.9 Refer to the OSPF command exhibit.
Which effect does the no-summary command option have?
A. It will cause area 1 to be able to receive non-summarized inter-area routes.
B. It will cause area 1 to not receive any inter-area routes and will use a default route to reach networks in
other areas.
C. It will cause area 1 to not receive any external routes and will use a default route to reach the external
networks.
D. It will convert the NSSA area into a NSSA totally stubby area.
E. It will convert the stubby area into a NSSA.
F. It will disable OSPF auto-summary.
Answer: B
Cisco자료 642-883 642-883시험문제 642-883 pdf
NO.10 When configuring IPv4 and IPv6 IS-IS routing on Cisco IOS XR routers, which three statements are
correct? (Choose three.)
A. By default, a single SPF is used for both IPv4 and IPv6, so the IPv4 and IPv6 topology should be the
same.
B. By default, the IS-IS router type is Level 1 and Level 2.
C. All IS-IS routers within the same IS-IS area must be configured with the same IS-IS routing process
instance ID.
D. By default, metric-style narrow is used.
E. By default, the IS-IS interface circuit type is Level 1 and Level 2.
F. The area IS-IS address-family configuration command is used to specify the IS-IS area address.
Answer: B,D,E
Cisco최신덤프 642-883 642-883 dump 642-883 pdf
ITexamdump의 C_TADM53_70덤프의 VCE테스트프로그램과 70-583덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 74-324시험에 대비한 고품질 덤프와 98-372시험 최신버전덤프를 제공해드립니다. 최고품질 ICBB시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기